Hello and welcome to this lecture in this lecture we start the configuration of the HQ 48 fire or so
what's the plan.
Well first we'll configure IP addressing on Pt. 1 2 and 3 and then we will also enable the specific
services that are needed on on the port two and three.
So on port two I'll enable ICMP connectivity so that I can test reach ability from the land P.C. to
through the firewall and on port three.
I will enable SSA each.
What else HDP HDP has for management purposes.
And by the way on the 48 firewall there is no such thing as the delegated managed management port.
As you can see we have available on the Cisco SC every and each port of the 48 firewall can be the management
port.
It really depends on what services do you make available on that specific port.
So because I am going to connect through a HDP on the on the AC on the EU 48 firewall on port three
I will enable a GDP and a GDP.
And that's the the main idea.
So now just right click on the firewall and say console and I will also increase the font a little bit
so that it's easier to see from your side.
So let's say 18 and apply now let's say admin and just click on enter and that's the that's the default
username and password with admin as username and no password just click on enter.
So let's now concentrate on the configuration.
Let's start with port number one so you'd say configure system interface and then you'll see Eddie port
one and say set IP question mark.
Now the council is waiting for IP address and subnet mask.
So in this case it's Eddie.
Eddie.
That Eddie that Eddie and I would say slash 30
uh
80 81 81.
Actually it's 80 it's the subnet subnet IP.
So eighty one cannot change dynamic IP so by default port 1 it's configured to be in DCP mode.
So in order to get its IP through through a DCP.
So what we need to do its mode.
And even if you go to a question mark you see that the options available are static DCP and PPO.
So first we have to say set mode steady.
And then to apply our IP IP address if we want to test the configuration you say show system interface.
And because we're in this in this specific mode you do not show us the IP address let's say.
And this way we also apply the configuration.
And so again show system interface and question mark.
And we see here Port 1 it's static and has this specific IP address.
Let's now also enable our IP routing.
So we will continue a default rollout on the HQ for the gate in order to point to the Internet router
and we will say configure rather static and let's now edit the first entry in the writing table.
So EDIT 1 If you now hit the question mark you have so set question mark you'll see that some of the
options have an asterisk.
So destination and device let's say set destination.
Question mark.
Let's say 0 0 0 0 and 0 0 0 0 and also say set device.
Question mark it's waiting for a port interface or this case in this case it's port 1 and said gateway
if we want to also configure it.
In this case it's 80 that 80 the 80 that 80 to as we can see in the genius street topology.
So with this said we have we have also configured the IP routing the default road on the HQ for the
gate pointing to the Internet rather.
Now let's say exit.
No.
Sorry.
And let's configure also port to and port three.
So configure system interface.
Now we will say edit port what port to and let's say set IP and it is one end to that once say that
one that one.
And it's a sledge 24 mass.
And we also want to enable being ICMP so that again we can test the connectivity between land P.C. and
the firewall.
So we will say said allow access and ping.
Now let's move on to port number three.
So we just have to say next and edit port 3 Let's configure the IP address.
So set IP 172 that sixteen that 100 to 1.
And it's a sledge 24 and we also have to configure access.
So we have to permit some services in order to become a management port so that we can access it through
a GDP set allow access let's say even though we will not use a SSA will say that allow access.
Let's just look for the options.
So being a GDP is as I say just an MP is GDP and so on.
So what we need is a GDP a GDP s and that's it.
So now let's say and and show system interface.
If you Now hit enter you you'll have the configuration of all of your interfaces.
But what else you can do you can say show system interface and question mark so that you have a fast
delivery of four of the important information for port one with this IP address port to and port three.
So this concludes this.
This lecture we now have configured all of the IP addressing on the issue 48.
Let's move on to the next lecture where we will continue with the branch 48.
Thanks a lot.