1
00:00:00,330 --> 00:00:03,030
Hello and welcome to this lecture in this lecture.

2
00:00:03,030 --> 00:00:08,070
We continue with the configuration of the site to site VPN and specifically we will be connecting to

3
00:00:08,070 --> 00:00:18,060
the branch 48 firewall so again admin no password just log in skip everything else and let's jump to

4
00:00:18,060 --> 00:00:22,120
the VPN section on the on the left side on the menu.

5
00:00:22,200 --> 00:00:27,190
So after the page loads will now click on VPN and go to IP SEC reserve.

6
00:00:28,750 --> 00:00:36,870
So again we've been set up it's a site to site VPN tunnel the remote device is 48 no net between sites.

7
00:00:37,420 --> 00:00:44,090
So let's say here HQ this is the the name of the VPN setup and click next.

8
00:00:44,110 --> 00:00:50,710
Now what is the IP address configured on the public facing interface of the 48 firewall.

9
00:00:50,710 --> 00:00:53,600
So it's 80 1880 and 81.

10
00:00:53,710 --> 00:01:02,020
So let's configure this so 80 80 80 not 81.

11
00:01:02,050 --> 00:01:08,360
Now outgoing interface it has been detected we are writing lookup now because we have a default route

12
00:01:08,860 --> 00:01:12,630
configured on this port one facing facing the Internet.

13
00:01:12,730 --> 00:01:15,910
That's why it has been ordered completed here.

14
00:01:15,910 --> 00:01:20,110
Now the pressure key I would click on the ISO that you see what I type.

15
00:01:20,200 --> 00:01:25,160
Said that it's 14 it and we will just click next.

16
00:01:25,180 --> 00:01:27,200
Now what's the local interface.

17
00:01:27,310 --> 00:01:32,610
So the local interface it's port number two you can see the IP before address one into 168.

18
00:01:32,680 --> 00:01:34,640
To that one slash 24.

19
00:01:35,200 --> 00:01:42,470
So I would click this the remote subnet so the remote private IP address or private IP subnet it's 1

20
00:01:42,470 --> 00:01:46,810
9 to the 1 6 say that one 0 slash 24.

21
00:01:47,890 --> 00:01:55,750
So again traffic between these two sites one of these two IP before subnet 2.0 and 1.0 will be included

22
00:01:55,750 --> 00:01:59,050
in the tunnel and it will be protected.

23
00:01:59,080 --> 00:02:08,470
Now I'll just click Create so short on a list and this is basically our setup.

24
00:02:08,650 --> 00:02:10,460
So that's all very simple.

25
00:02:10,540 --> 00:02:18,160
Just a couple of clicks but you have to know what to what to what to fill in in the in the details and

26
00:02:18,160 --> 00:02:22,380
the configuration is up is absolutely very very simple.

27
00:02:22,420 --> 00:02:27,100
By using the IP stack wizard and you can see that there are only three steps.

28
00:02:27,340 --> 00:02:32,830
So that's all with the configuration on the branch firewall as well in the next section we will do some

29
00:02:32,890 --> 00:02:36,130
verification testing and wrap up the whole section.

30
00:02:36,130 --> 00:02:36,700
Thanks a lot.