Hello and welcome to this lecture in this lecture we will build our first apology using QM K VM images
and specifically we are going to install some of the most important appliances Within Cisco vendor so
ISV Layer 3 rather I Villar to switch and the SCV appliance.
Now in order to use them we will first have to install them.
So let us navigate to process all devices and look for ISV.
When I tried to drag it into the topology workspace it will showed me this.
This specific message that we need to add an appliance.
So let's click.
Next we will run the appliance on the genus 3 VM is the recommended.
But please know that it is also the the only option and I'll click Next Gen S3 server requirements is
okay and you can continue the installation.
So this is fine.
I will click next and now they are looking for some specific images.
So for example when I try to install the 15 that 6 to TI it's looking for this specific image but it
also is looking also for this eye as we start up config.
I am G so image so it is missing.
So for this reason I will hit download here.
But before that let's look at this image.
So why does it does it say that it has found this image.
Because if I go into the downloads in my downloads folder I also have this image.
So this is the image VII.
As for 15 6 2 t running train.
So for this the startup config I am G I will hit download it will go to search source that net and it
will download this missing file that I am G now the download will start it has finished.
Let's move back.
So if I look it here now.
Yes it appears in the downloads folder.
So now if I click refresh it looks ready to install.
So for this one it has also the image and the startup config so I will select 15 6 to tee and hit next.
It asked me Do you want to do would you like to install Cisco ISV version than the specific version.
Yes it will use this Q M binary.
It is now uploading this this image and I can click next.
The following settings are going to be used.
So adapter type its e 1000.
It will use 5 1 2 RAM so half of gig and it is also important to note.
This kind of information because it really depends on what kind of P.C. or Mac laptop you have.
Honestly speaking so resources are not infinite so use it wisely.
The only drawback is that you would have to run smaller typologies and not build large ones.
But if you if you build a big big topology you will have to run it like half now and then move to the
other half and do the configuration and and try to deal with this.
This kind of setup.
So that's why the the ram it it's it's important.
Remember so for the AI as filler 3 rather it's 5 1 2 Ram.
So let's click next.
Now there is no default password and also no enabled password.
So if I click finish it will now appear in the installed and available plants.
You can see that it's the the the font.
It's bold now.
It's available for use.
So I hit.
OK now let's do the same for the ISV.
So it's multilayer switch layer 3 speech.
Basically you can use it also for routing again next next next.
Looking for files.
Let's see what they're asking.
So in this case I don't need any startup.
It will look for this image.
The virus L2 15 2 4 0.
Let's look at the downloads folder for 0 5.
Yes this is the 1 4 0 5 5 so because it's there it's now ready to install.
So very easy hit next.
Yes I would like to install this version using this binary next Ram 7 6 8 so 768 next and finish.
Now I also have the latter two running.
Let's look for the SCV
SCV next.
Next.
Now as you have seen in the windows installation we don't have we don't have any kind of any any of
these versions.
So let's look.
Here we have 9 8 2 6 2 and 6 1.
And they're also looking for specific name naming convention to say so.
So let's try to run the list.
The latest code though 9 a 2 will create a new version version name.
Let's try to mimic what's inside already has a v 9 8 2 OK.
And we will do an import let's go to now loads 9 a two open
as you can see now it's ready to install.
So I have defined a new version inside the SCV.
It's 9 a to it now although I have done the the import it now says that this is the the image that I
should use and I don't want to do that.
So again let's try.
Import
so it still shows me that I should use this one.
Let's say next.
Yes I will live it as it is next.
And please know that it now requires two gigs of ram.
So per appliance next.
And finish.
Now if you go into the into this working space and say configure template this is where you would change
this image because as you've seen we couldn't do anything there.
So downloads 9 a two open uploading this new image and the correct one it shows now a CV 9 8 2 cue card
2 and I hit.
OK now let's try to drag one of this.
And also let's look for the ISV and I'll take a switch.
So the image VII is two it's missing.
No worries we'll fix that.
That's why we're here.
So configured template that's going ending into the hard drive and say browse.
Go into your specific folder where you have the image.
This is my image.
I will hit.
OK.
And now the image is being uploaded and hit.
Okay let's try again.
We have had the same problem within the Windows installation.
Let's take another router.
This one is missing as well.
No worries is configure template.
Let's upload again.
This is the layer 3.
So this one open and.
OK.
This is something you have to only when you first set up or first lab with these images then you'll
you'll see that it works.
Very good.
So again and let's take also.
Well actually no.
This is pretty much enough let's connect all together.
Perfect.
Now stop it and start the images
let's console now to all the devices and I will also increase a little bit size
so console
increase the size of them
so they are now expecting us to connect to the SCV through through a v NC Veera so S6 OSX OS X VANOC
support is limited.
If you have trouble connecting to a device please use an alternative like chicken of the VANOC.
OK so this is the IP.
I have another VM severe installed on my laptop and I'll insert this IP 172 not 16 so 16 dart 1 1 7
that 1 2 9
don't warrant more me about this and connect.
Yep.
And I think it's working.
So the digital signature of the running image verifies successfully.
This is good news.
Yeah.
So basically the um the V.A. viewer by default the screen sharing app on the Marquis will do many many
things many many bad things to you and it will not work.
So that's why I am using another software.
It's called Vinci Europe.
And this one works perfect so I have used the IP that was there in the screen sharing app and instead
is here in Vinci here and now we can see that the SCV is building up.
Also these other two devices look like.
It looks like they're they're working.
So in the left it's the eyes v layer to the switch.
I'm waiting for it to put up and in the right I also have the.
The other one.
So this one is the the roller.
So let's wait for them to boot up.
I will have a fully functional topology if all I would consider that it is a fully functional topology.
If I assign some IP addresses between the router and the SCV and I will see them that they respond to
to ICMP packets.
So this is the the end goal of the session.
So let's see if everything is working now.
Putting the kernel building the configuration so it will take probably another 1 minute or so
so the roller is working now its configure some IP addressing
10 0 0 1 and let's say mask 24.
So again 10 0 0 1 mask 24.
No of course not.
Interface Exhibit 0 by 0.
So IP address 10 0 0 1 slash 24 no shut
show IP interface brief 10 0 0 1 Good.
Now the switch has finished booting up so almost done with a switch as well.
Let us configure the switch and let's say interface Exhibit 0 by 0.
Interface range gigabit 0 by 0 up to gigabits or by 1 no shut
show interface status.
They're fine.
Now we can move to the NSA.
So the NSA will use gigabit zero by zero.
So interface will be configured terminal no interface gigabit zero by zero.
Let's say name.
If I'm outside.
IP address 10 0 0 2 2 5 5 5 5 5 5 0.
Show IP address 10 0 0 2.
Let's enable ICMP buying show debug and initiate an ICMP being from the Cisco I say 10 0 0 1
show.
Run
actually show interface ip brief I believe.
Show interface ip brief I believe.
The interface.
Yes it's shut down so configured terminal again interface will be 0 by zero and no chef show running
configuration interface it'll be zero by zero.
It shouldn't be fine being 10 0 0 1 and yes it's working as you can see I have ICMP packets being debunked
we've seen coming from 10 0 0 2 and we're responding with our self as the source 10 0 0 1 and going
to destination 10 0 0 2.
And this concludes the lesson the lesson.
It means that the SCV is functioning.
It's working the air the rudder is also running around working because we are now basically responding
to the ICMP packets and because in the middle we have an ISV layer to switch that permitting packets
from one side to the other.
It means that as well this device is working.
So there you go you have a fully functional topology.
Yes it's more one but from this point you can just elaborate and build bigger and bigger and more complex
typologies.
So this is how you build and initiate your labs with ISV layer to layer 3 and a savy QM images.
So thank you for viewing and see you in a feature lecture.